Infrared: Reset Address

Here we wan’t to describe the Reset address (CV31+32). You can set this in the IR Receiver. Following example: You drive on your layout until the signal red, the locomotive stops. You take your locomotive off the track and pack it up. At a guest layout you put your locomotive on the track, but the locomotive is blocked by a red signal from the previous trip! Now you need…

Read More

Infrared: List of supported decoders

Here you can find a list of supported decoders for our Infrared System Decoder Function CV Minimum firmware Decoder with SUSI BIDI eMOTION LS SUSI-BIDI CV 49 Value+16 4.1 eMOTION XLS SUSI-BIDI CV 49 Value+16 4.1 eMOTION XLS-M1 SUSI-BIDI CV 49 Value+16 4.1 eMOTION XLS-OnBoard SUSI-BIDI CV 49 Value+16 4.1 eMOTION XL-M1 SUSI-BIDI CV 49 Value+16 eMOTION XL II Plug SUSI-BIDI CV 49 Value+16 eMOTION XXL II SUSI-BIDI CV…

Read More

Infrared: Control via contacts

Here we want to describe the control of the IR receiver via the contact inputs of the decoder. If your decoder does not have a SUSI-BIDI interface (see here), you can still use our infrared system. Automatic or switching functions are not possible here. Connect the receiver as shown below. As an example, an XL decoder was chosen. In the IR receiver, set CV 62 to 2 to activate…

Read More

Infrared: Block signal mode

Description of the Block signal mode with our IR System. You need additional Track Contacts and a Feedback module. Input A set the signals to red, input B set the signal to green. The last contact (4) has a special function. He releases the block signal again. If your block signal layout is a circle, you can remove the last contact. Therefore you have to connect 1A with 3B….

Read More

RC Receiver does not work

Sometimes the elimination of radio problems can be very easy. The cause is sometimes “animal nature” as you can see in the picture. Here ants have disturbed the Massoth Bus by being run through the contacts. The voltage meant Unfortunately for the ants to death. Since the ants are still at the contacts, thereby the signal is still disturbed. After cleaning the contacts, everything should work again.

Read More

Identification of the decoder

Identification of the decoder when installed Often you have the problem with a hand purchased loco, not knowing what decoder is installed. There is some advice on how to get information about it. As an example using our navigator in CV reading mode You can identify the manufacturer in CV 8. Based on the value you can then assign the manufacturer. Below is a list of the most common…

Read More

Definition of Switching Outputs

Here we would like to briefly explain what reinforced and unreinforced switching outputs of our decoders are. Below is a drawing that explains how the outputs work (As an example with a XLS): A reinforced output is connected between + 22V and the switching output. If the switching output is turned off, there is +22V output, therefore is no potential difference is and no current flows. If the switching…

Read More

Uncoupler connected to LGB Onboard Big

Attached you can find the connection diagram of the big LGB Onboard Decoder. Uncoupler 1 will be connected normally. Uncoupler 2 cut off the plug and connect red to + F2 brown to – F2 black to black of decoupler 1 You have to decide whether you want to dispense with the smoke unit. Programming: CV49=32 CV56=32 CV51= 1-8 (Desired button F1) CV57= 1-8 (Desired button F2) LGB-ZD-3A-komplett.pdf

Read More

By continuing to use the site, you agree to the use of cookies. More Information

Die Cookie-Einstellungen auf dieser Website sind auf "Cookies zulassen" eingestellt, um das beste Surferlebnis zu ermöglichen. Wenn du diese Website ohne Änderung der Cookie-Einstellungen verwendest oder auf "Akzeptieren" klickst, erklärst du sich damit einverstanden.

Schließen